| |
Posts Tagged ‘clean<’
Posted in General Building on Aug 27
Even the roof of a well-constructed metal shed may eventually submit to the elements, leaving you with a problem to resolve. Noted for their structural stability, metal roofed sheds can be a useful asset on your property, provided you keep things well maintained. Sam, one of our London general builders, has the following sage advice to offer: “minor rust patches and small holes in your metal roofed shed can cause water intrusion in the form of unwanted leaks. You must attend to these leaks as soon as possible if you want to keep the appearance and structural integrity.” Wise advice indeed – thank you Sam! 
What You’ll Need
- Metal roof mesh
- Metal cutters
- Wire brush
- Broom and ladder
- Trowel
- Roof cement (urethane)
Off you go!
Begin by wire-brushing the damaged section of the shed roof, in order to remove all loose and flaky material. Use the broom to brush away the dirt and debris, and make sure that everything is dry before proceeding. If building repairs are not your forte, you can find a general builder right here on Mr-Skill. That way, you know that you’ll be getting the best prices from any one of our many rated members.
Ready to Roll 
Using the roofing mesh, cut two identical square patches with the metal cutters, ensuring that they are over-sized to cover the holes or rusted area – the rule of thumb is to overlap by at least two inches. Now, using the trowel, work the urethane roof cement around to cover the area under repair – as always, read and follow the instructions on the pot.
It is time to press the first patch into the wet roof cement. Spread a further even layer of the urethane coating over that mesh using your trowel. Add the second square of mesh, and apply a final even layer of the urethane over the top. You may have to work the wet roof cement in – this is to ensure a complete and even spread. Finally, always be guided by the instructions and allow sufficient drying time.
If this all proves too hard…
Many people simply don’t have the patience or the necessary know-how to repair things for themselves around their homes. If this describes you, get your general builder quote right here on Mr-Skill, then just put your feet up and relax! A soothing cuppa will always assist!
Tags: asset, clean, debris, dirt, find a general builder, general builder, get a general building quote, leaks, London building expert, mesh, metal, metal cutters, metal roof, repairs, roof, rust, structural integrity, trowel, urethane roof cement, water, wire brush
Posted in General Building | Comments Off
Posted in Plastering & Drywall on Jul 25
Once you have installed two drywalls meeting at right angles to each other, you are going to need to finish the join where they meet at the ceiling, using flexible correctly mitred cornice lengths. Cornice (or coving) of course comes in many shapes and sizes and is even available in easy-to-use light-weight polystyrene these days. This attention to detail will not only finish off the job nicely, it covers up ugly gaps and imperfections too. 
What You’ll Need
- Sandpaper
- Jointing compound to bond the cornice
- Putty knife
- Cleaning cloth
- Suitable lengths of cornice with correct mitre angle
Although not a difficult job, we are of course assuming that your drywalls are in place and that it’s just a matter of adding the ceiling trim to hide the gaps and join-lines.
Been There, Done That!
Fred is one of our long-standing London plasterers, and he always cringes when he receives an enquiry to quote on a plastering job that’s a botch up. While Fred appreciates that there are a number of very able-bodied DIY-types around, he also knows that finishing the gaps where wall meets ceiling is a skill that takes time to master.
Finishing First
You’ll need to smooth any rough edges on the drywall sheets by sanding them finely. Then, wipe the area with a damp cloth to remove the dust and dirt. Allow the surfaces to dry thoroughly.
Time to Glue 
Read the instructions on the bonding agent carefully and then apply as required to the inward-face of the cornice. Remember to run the glue right across the corner – that’s where the two cornice lengths will interlock neatly.
Mounting the Cornice
After observing any recommended waiting time for the bonding agent to dry, mount the cornice in position and press down gently across the full length. Wipe off any surplus glue. Once the glue has dried, you can fine-sand the surface prior to painting.
Call in the Experts
Here at Mr-Skill we fully understand that not everybody is DIY-minded, and may very well need professional help with such jobs. No problem at all, because that is the name of our game. So, rather find a plasterer with minimum fuss, and the good news is that we have some eye-catching specials running right at this moment too. You could even get as much as 30% off, but hurry!
Tags: bonding compound, ceiling, clean, cornice, dirt, drywalls, dust, find a plasterer, gaps, glue, london plasterer, mitre, paint, plaster, plastering quote, rough edges, smooth, specials, wall
Posted in Plastering & Drywall | Comments Off
Posted in Tiling & Flooring on Jul 19
It’s quite amazing how even knowing about a cracked tile in the home can have us wondering just what to do about it. One of our London tilers summed it up quite nicely when he mentioned how his colleagues seldom thought to offer the homeowner a couple of extra tiles to hold as spares for future breakages. Easy for him, we hear you say, but how difficult is repairing a tile in any case? The answer – quite simple, if you observe the following advice offered by Mr-Skill: 
Taking Stock
Throwing your arms up in frustration is not going to solve the problem, but following these simple steps is likely to have you smiling. Even so, some people are simply not motivated to make repairs like this themselves. If this describes you, rather find a tiler to do the job for you. Mr-Skill has a number of experts lined up. They have all been pre-screened, and the good news is that there are some great discounts on normal prices but you ought to move fast!
What You’ll Need
A special epoxy glue and catalyst set – buy this at any hardware store, but make sure you choose one suitable for ceramic tiles. Also have a putty knife or paint scraper available to mix and apply the resin.
Buy a small sample tin or bottle of oil-based paint to match as closely as possible the tile colour. Oh, and get yourself a small tin of clear polyurethane lacquer too, not forgetting a fine-artist’s brush. If this all sounds complicated, you could also get a tiling repair quote on Mr-Skill.
Step 1
Clean the tile and surrounding area thoroughly, and make sure the wall or floor surface is dry before you start the repair.
Step 2
Mix sufficient epoxy glue and resin together, observing the manufacturer’s instructions carefully. Now fill the crack with the mix, using the paint scraper or putty knife.
Step 3
Wipe off any surplus above the crack line and leave the repair to dry completely.
Step 4
Now you can carefully paint over the repair and leave this to dry as well. 
Finally, it is advisable to apply a coat of polyurethane lacquer over the painted area and leave it to dry. Job completed, and it’s time to pop the kettle on and make a nice cuppa to enjoy while you admire your handiwork. Don’t forget to thank Mr-Skill for this wonderful free advice.
Tags: brush, catalyst, clean, cracked tile, epoxy, find a tiling expert, fixing, floor, glue, homeowner, lacquer, london tiler, paint, paint scraper, polyurethane, putty knife, resin, tile, tiling quote, wall
Posted in Tiling & Flooring | Comments Off
We had a call from a customer the other day, who was confused as to why a cleaner wouldn’t take some old acid containers away – especially after they loaded all the cardboard boxes they cleared from his garage. We thought it would be a good idea to explain the difference, and to generally set the record right.
- Generally speaking, cleaners tidy sweep and clean a home or office, pretty much the same way we might do ourselves, if we
 only had the time. In the course of this, they bag the contents of waste-paper baskets and rubbish bins, so you can leave these out on the next council collection day.
- If you want the service people to take the bags down to the council depot as well, then you need to ensure they include this as an option on their cleaning quote. That’s because this job will involve extra time and petrol, and they’re entitled to their compensation.
- Certain types of materials and chemicals are classified as toxic, as they could harm an operator at a landfill site who comes in contact with them. The government has established rules for their safe disposal. Councils have procedures in place to make this possible.
 Our client who called us actually needed to find a waste disposal expert to remove the acid containers, not a cleaner. They would be equipped with specialist protection to avoid contamination themselves. It’s vitally important to understand the distinction, and not to pressurise a regular cleaner to take risks.
Mr-Skill has both kinds of service people on their books. Our customers have rated almost all of them down the years too.
Should you require the services of a top-rate London cleaner, or assistance with cleaning or waste disposal almost anywhere else in Britain, why not log onto our website and log your request right now? Our operators are on standby, and waiting for your call.
Tags: acid, bag, chemical, clean, cleaning quote, container, contaminate, contamination, council, depot, disposal, empty, find a waste disposal expert, garage, garbage, harm, hurt, landfill, london cleaner, material, protection, rubbish, specialist, sweep, tidy, toxic, waste
Posted in Cleaning Services, Disposals & Waste Removal | Comments Off
You have made your mind up and you have decided to clean your garage – again! The first thing you stumble upon is loads of leftover paint pots in various stages of decay. What do you do next? Well, if you are like most of us and are environmentally principled, you should be thinking the three “R’s”. That is, reduce, reuse and recycle.
Does this sound a little hard for you? You could also get a waste removal quote from Mr Skill by clicking on this link. This will direct you to a number of cleaning services. Next time you find a decorator, why not ask them to remove the leftover paint after they have finished?
Reduce – If you find that there’s always some paint left over from a job, this tends to suggest that you are buying too much in the first place. Speak to your friendly paint shop and ask them to calculate your paint requirements next time, based on the measurements you provide. Most paint pots also provide coverage guidelines on their labels.
Reuse – As long as you store leftover paint properly – meaning correct sealing and storage – you can keep the paint for quite a considerable time.  Tip – wipe the rim of the open paint pot clean and replace the lid tightly. Make sure you have a decent seal and then invert the pot. If you store the pot upside-down like this, you should have an airtight seal that will prevent a skin forming under the lid.
Recycle – Check with your local authority when it comes to recycling empty paint containers. The chances are good that these can be handed in at your local waste station. If your paint containers cannot be recycled, dispose of them responsibly as general household waste.
Now my old mate Ray, who’s been a professional London decorator for more decades than he cares to remember, suggests that if you do have usable leftover paint that you are never going to need, then you should try donating it instead. Check your local charity shop for advice. Better still. Make sure the cost of disposing of messy paint pots is included in the painter’s quote next time. This information is provided by Mr-Skill as a public service.
Tags: buy, calculate, charity, clean, container, dispose, donate, find a decorator, garage, leftover, lid, london decorator, measure, old, paint, painters quote, pot, recycle, reduce, remove, reuse, shop, skin, store, tin, waste
Posted in Painting & Decorating | Comments Off
Whether you Find a Decorator on Mr-Skill or do the job yourself, you inevitably end up with left-over pots of paint. Those with just a few scrapings in them are best thrown away. Those still at least a quarter full could be worth preserving for touch-up jobs.
 Reseal Quickly – Air is the enemy of paint because paint’s supposed to dry in its presence. Clean both lid and tin carefully where they come together. Insert a sheet of film or tinfoil. Close firmly to achieve an airtight seal without causing any distortion.
Label the Tin – Begin to clean your brush by painting a colour-patch on the tin in a way that does not cover up any important information. Use a laundry marker to note the dates when bought and used, and the colour code if the paint was specially mixed.
Store Away Sensibly – I know a London Painter who insists in storing paint tins upside down so that the paint remains above the film and not beneath it. I’ve followed his advice and found it works quite well. In any case, store the tin away from extreme heat and cold.
 Using Old Paint – Paint has a limited shelf-life and many manufacturers suggest that it should be used within a year of being purchased. Don’t be tempted to bring down the cost of a Decorating Quote by using paint that’s gone beyond its usefulness. In any case, make sure it’s strained through a fine mesh sieve or piece of muslin, and into a clean container and well stirred.
Storing paint is really only really useful when you have a plan to use it shortly. This could be when you are half-way through an upgrade, and just want to brighten up a wall. In other instances it may just be an excuse to accumulate more clutter.
Be brave. Know the difference. Why not give your old paint tins a fresh view on life instead.
Tags: air, airtight, clean, close, code, cold, colour, container, date, decorating quote, distort, film, find a decorator, foil, heat, label, left over, leftover, london painter, mark, muslin, paint, patch, pot, reseal, sample, scrap, shelf life, shelflife, sieve, store, strain, tin
Posted in Painting & Decorating | Comments Off
That’s right. The snow may be lying heavily on the ground this year, but the days of warmer Spring are not far away. This is traditionally the season for clearing everything out that you do not want.  Perhaps you should start planning earlier, before all the waste-removal firms are booked out. We offer an exemplary service in this regard. Mr-Skill is able to offer the following range of helpful services when you are in the mood to tidy up.
Waste Management – The professional removal of potentially toxic industrial and commercial waste to Council specifications. Our specialists are equipped with all pre-requisite waste management safety gear and will complete their task responsibly.
Garbage Disposal – Sorting of non-toxic “safe” commercial and domestic garbage into categories, and delivering to re-processing plants and Council garbage disposal tips in accordance with your local bylaws.
Rubbish Removal – Disposal of general “clean” rubbish in an environmentally friendly way according to local regulations. Many town councils award street rubbish removal contracts to our agents.
 Garden Clean-Ups – A broad-based horticultural service. When the snow has melted (and that won’t be too long now) you’ll be glad you booked a garden clean-up and de-weeding service while contractors had room on their calendars still. As with all our contracts, the refuse will be responsibly disposed.
Unlike similar websites we charge consumers nothing extra for our service. In fact the overwhelming feedback is that our contractors charge lower rates. That means you win twice when you contact Mr-Skill. You win the first time because you get a reliable service. The second benefit is it costs you less.
Can you afford not to investigate this further? What’s more, you get your space back too.
Tags: clean, clear, commercial, council, deweeding service, dispose, domestic, environment, garbage, garbage disposal, plan, professional, prunings, regulation, remove, reprocess, responsible, rubbish, rubbish removal, safe, sort, specification, spring, springclean., tidy, tip, toxic, trash, waste, waste management, weeds
Posted in Cleaning Services, Disposals & Waste Removal, Gardening & Landscaping | Comments Off
With winter upon us – and a freezing one at that – many people across the United Kingdom are experiencing problems with their guttering. These can include gutters filled with ice collapsing, and nowhere for water to go when the thaw comes. Is it possible to prevent this? Well, we can’t prevent a blizzard, but we can Find a Roofer to take preventative action for us.
 These are some of the things worth considering when you are busy getting Roofing Quotes.
• When snow gathers on a roof it should thaw gradually without causing problems. But, if you have heat build-up above your ceiling then it might melt all at once, blocking gutters that then freeze up. Two things to do. Check your ceiling insulation, and make there’s provision for any heat to escape.
• Ensure the water entering your gutters can flow smoothly through the down-pipes. This means cleaning them thoroughly twice a year (before and after winter) and testing them from time to time.
• Matt, my London Roofing friend swears by heat tape you can stick along the gutter. Personally, I don’t feel that this is necessary provided you keep them clear.
 • Snow guards can provide an extra line of defence, especially if you live up in the north, and they can help keep the gutters clear in summertime too. In fact, I strongly recommend them.
Hopefully you did this already and your gutters won’t come crashing down from the weight of ice this winter. Please do be careful about venturing on the roof yourself to clear excessive snow. It’s just not worth taking risks.
And that’s where Mr-Skill comes in. Did you know that you can Find a Gutter Man right here who’ll clear your blocked gutters promptly, as long as it’s not actually snowing? All our trades come highly recommended too, and rated by our customers. What’s more, you pay nothing for our services.
Tags: blizzard, ceiling, clean, clear, collapsing, down pipe, find a roofer, freeze, freezing, gutter, gutterman, heat, heat tape, ice, insulate, london roofing, melt, roofer, roofing quote, snow guard, test, thaw, ventilate, water, winter
Posted in Roofing, Gutters & Drainage | Comments Off
Posted in Plastering & Drywall on Feb 01
Damp is an on-going problem in many homes in Britain, and that’s not just in the older ones either. Water, especially when forced by wind can find its way inside an outside wall through the tiniest of cracks. After the leak is fixed, it’s time to Find a Plasterer to fix the evidence that alerted us to the damp in the first place.
The Problem
The water has leached the cement away leaving weakened plaster that will eventually come off. The only solution is to hack it out and replace it. You have a choice, though. You could Ask Mr-Skill to Arrange a Plaster Quote, or you could have a go at it yourself.
 Repair Stage One
You have to get rid of the damaged plaster at least a foot above any visible damage or residual salts. If the damp was low down, then you must in any case remove the plaster to three feet above floor level. Brush away every grain of loose material. Complete the job with a vacuum cleaner – you may wish to do this when the wife is out shopping.
Repair Stage Two
This is a tip a London Plasterer taught me years ago. Put on a pair of disposable latex gloves. Make a slurry of cement powder and water with a cup of bonding liquid added – the final consistency should be like runny porridge. Brush this firmly over the space where the old plaster came out. This will allow the new plaster to adhere properly. Wash your hands and tools immediately. Allow the slurry to dry for a day.
Repair Stage Three
Make up a stiff plaster mix of 3-Parts sand to 1-Part cement. Apply this with a wide paint scraper or steel float across the entire surface roughly, and leave it alone for two hours to set. Apply a fresh mix of plaster that stands just proud of the surface. Work this off with a straight edge later the same day.  Leave the job to cure for a week.
Repair Stage Four
Apply a moist mix of Polyfilla over the entire surface. When it’s totally dry and the surface has gone a little powdery, finish the job off with an a sanding block or orbital sander, using medium-grit paper. After that, you are ready to decorate!
That’s all very well in theory, but do you really have the time to spend on this? If not, that’s where Mr-Skill comes in. We provide a matching service between customers and tradespeople. Unlike some others, we don’t add a penny to the cost of jobs.
Tags: adhere, bond, brush, cement, clean, consistency, crack, cure, damage, damp, dry, dust, exterior, find a plasterer, float, get rid of, glove, grit, hack, london plasterer, mix, orbital, outside, paint scraper, plaster, plaster quote, polyfilla, powder, remove, replace, salt, sand, scraper, set, slurry, stick, straight edge, tip, wall, water
Posted in Plastering & Drywall | Comments Off
Posted in Electrical Work on Jan 23
The last thing you need in any circuit is a dry joint, by which I mean two wires twisted round each other or even worse. In a home, this can cause the power to keep on tripping, while in the low voltage world the result is a random electronic fault.
 From time-to-time it’s necessary to get a soldering-iron out. Before you rush around looking for an Electrician Quote it might just be possible to do the job yourself.
• Preparation Clean both parts that you are planning to solder into a joint. Hardened, damaged wire is a recipe for disaster so make sure everything is shiny new by stripping off a fresh end. While at it, remove any vestiges of solder if you’re repairing an existing joint. That’s because solder does not stick to itself at all well when not fresh.
• Tinning Heat each surface in turn until it just melts a bead of solder. Work this back and forth until you see a little amber liquid appear. That’s the tinning that’s the meat in a good joint. It will be HOT. Allow the material  to cool down naturally before you touch it with your hands.
• Soldering Mount the larger of the pieces to be joined securely in a vice. Heat up its surface until solder melts instantly on it. Place the other tinned piece in the pool of solder, remove the soldering iron, and wait until the surface of the melted solder goes slightly dull. Allow the joint, which will be HOT to cool naturally.
If you have a soldering iron that’s in good order and you have the time, you don’t really need to Find an Electrician, do you? But beware one thing, and that’s a bad joint. A London Electrician I know tests his apprentices’ work by seeing whether he can pull it apart.
Tags: bead, circuit, clean, cool, dry, electric, electrician quote, electronic, find an electrician, flux, fresh, heat, hot, joint, london electrician, melt, preparation, remove, solder, solder iron, strip, tin, tinned, vice, wire
Posted in Electrical Work | Comments Off
|
Subscribe to our RSS Feed