| |
Posts Tagged ‘dry<’
Newly installed drywall panels provide a flat wall surface, which is suitable for hanging wallpaper or painting after plastering, depending on your preference. Here, we are describing plastering itself, which is an essential step. If you do not feel confident, to do this yourself, rather find a plasterer through Mr-Skill. If you go ahead though, it is essential that you apply the dry wall compound in precise steps, in order to obtain the smoothest finish.
What You’ll Need 
Drywall plaster mix
Drywall tape mesh
Drywall tape tools
Respirator (facemask)
Non-slip drop cloths
Tips and Cautions
Remember you could also get a plastering quote from one of our craftspeople on Mr-Skill.
Use non-slip cloths to cover floors before plastering, and tape up door and window frames to prevent fine dust from infiltrating the rest of your home.
Apply several thin coats of plaster mix rather than one thick layer to avoid lumping.
When sanding down after the final plaster application, be sure to wear a facemask.
STEPS
1. Cover each seam on the drywall panel with the self-adhesive mesh tape, and avoid tape overlap where the vertical and horizontal joints meet.
2. Use a trowel to pack the plaster through the mesh and into the seams. Don’t forget to cover screw holes carefully in the panels.
3. Gently scrape off excess plaster while it is still wet, using a trowel.
4. Leave the plaster coat to dry properly, and then sand off any high points with a drywall sander.
5. Apply a second coat and repeat the process per the above guidelines.
6. Sand the final plaster with fine-grit paper and wipe clean. Apply a coat of plaster primer paint. Once this is dry, you are ready to paint.
One of our London plasterers has built and plastered more walls than he cares to remember, but he can never resist the look of satisfaction on the clients face when he completes yet another successful job.
Tags: coats, drop cloths, dry, drywall, drywall tape, find a plasterer, fine sand, london plasterer, paint, plaster mix, plastering quote, sand, sander, seam'trowel, skim, smooth finish, tape mesh, wallpaper, wet
Posted in Plastering & Drywall, Project Advice | Comments Off
Posted in Tiling & Flooring on Feb 27
First you notice that the grout between the tiles has begun to crack. You wonder whether it’s time to Find a Tiler. After that, the grout starts going darker in one spot. Finally, when you tread on a tile, it rocks slightly as the moisture squishes out.
 Fortunately, this is not the end of the world! The good news is that the tile is loose and will be easy to remove. After that, you can have a Plumber in to fix the leak, and perhaps even replace the tile afterwards yourself.
- Avoid your first reaction to lever out the tile. Chances are that you will chip it, and where on earth will you find a replacement one? One London Tiler I know wets the loose tile generously, and then uses a toilet plunger to create a vacuum and gently ease it out. Try it. You could just be pleasantly surprised!
- Depending on how bad the leak is, you may need to turn the water off. If the water is not bubbling out from where you removed the first tile, you may need to chase the leak by removing several more. This is easy when you gently tap a paint scraper
 underneath the middle of the tile, because the mortar will be water-logged.
- Find a Plumber on Mr-Skill to repair the leak. Then wait patiently until the hole the plumber left behind has dried out completely. After that, back-fill it with a strong mix of mortar, and get a Tiling Quote to put the tiles back and re-grout. If you do the job yourself, use an epoxy as there will be insufficient space for tile cement except where the plumber made the hole.
This information comes to you with best wishes of Mr-Skill, that friendly website where you can find every service that you need. These services include electricians, builders, plasterers, carpenters, gardeners and a whole host more besides. The service costs you nothing, and they are all rated too.
Tags: back fill, chip, crack, dark, dry, epoxy, find a plumber, find a tiler, grout, lever, london tiler, loose, moisture, mortar, paint scraper, plumber, plunger, rated, remove, replace, rock, scraper, service, tap, tile, tiling quote, vacuum, water
Posted in Tiling & Flooring | Comments Off
Posted in Plastering & Drywall on Feb 01
Damp is an on-going problem in many homes in Britain, and that’s not just in the older ones either. Water, especially when forced by wind can find its way inside an outside wall through the tiniest of cracks. After the leak is fixed, it’s time to Find a Plasterer to fix the evidence that alerted us to the damp in the first place.
The Problem
The water has leached the cement away leaving weakened plaster that will eventually come off. The only solution is to hack it out and replace it. You have a choice, though. You could Ask Mr-Skill to Arrange a Plaster Quote, or you could have a go at it yourself.
 Repair Stage One
You have to get rid of the damaged plaster at least a foot above any visible damage or residual salts. If the damp was low down, then you must in any case remove the plaster to three feet above floor level. Brush away every grain of loose material. Complete the job with a vacuum cleaner – you may wish to do this when the wife is out shopping.
Repair Stage Two
This is a tip a London Plasterer taught me years ago. Put on a pair of disposable latex gloves. Make a slurry of cement powder and water with a cup of bonding liquid added – the final consistency should be like runny porridge. Brush this firmly over the space where the old plaster came out. This will allow the new plaster to adhere properly. Wash your hands and tools immediately. Allow the slurry to dry for a day.
Repair Stage Three
Make up a stiff plaster mix of 3-Parts sand to 1-Part cement. Apply this with a wide paint scraper or steel float across the entire surface roughly, and leave it alone for two hours to set. Apply a fresh mix of plaster that stands just proud of the surface. Work this off with a straight edge later the same day.  Leave the job to cure for a week.
Repair Stage Four
Apply a moist mix of Polyfilla over the entire surface. When it’s totally dry and the surface has gone a little powdery, finish the job off with an a sanding block or orbital sander, using medium-grit paper. After that, you are ready to decorate!
That’s all very well in theory, but do you really have the time to spend on this? If not, that’s where Mr-Skill comes in. We provide a matching service between customers and tradespeople. Unlike some others, we don’t add a penny to the cost of jobs.
Tags: adhere, bond, brush, cement, clean, consistency, crack, cure, damage, damp, dry, dust, exterior, find a plasterer, float, get rid of, glove, grit, hack, london plasterer, mix, orbital, outside, paint scraper, plaster, plaster quote, polyfilla, powder, remove, replace, salt, sand, scraper, set, slurry, stick, straight edge, tip, wall, water
Posted in Plastering & Drywall | Comments Off
Posted in Plastering & Drywall on Jan 26
From time to time we find jobs posted in the wrong category on Mr-Skill. When this happens, we duplicate the listings in more appropriate categories. Plasterers are a case in point because decorators  attend to damaged plasterwork. We decided to clear up the confusion, and make it simpler to Find a Plasterer here.
The main job of plasterers is to mix, and then apply various types of plaster on internal walls and ceilings. From time to time they also coat outside walls with sand / cement render, pebble-dash, and stone-effects. Notice that plasterers do their work in bulk, and that there’s little point in asking for a Plastering Quote where it’s just a small repair.
Within these broad brush strokes, plasterers generally work in one of the following three sub-disciplines:
- Solid Plastering – Applying wet finishes to interior walls and ceilings, and sometimes pebble-dashed effects on outside walls
 Fibrous Plastering – Creating ornamental cornices and ceiling roses using special plaster reinforced with fibre
- Dry Lining – Installing interior drywalls on frames, for others to decorate later.
Larger firms, especially Plasterers in London may take on all three kinds of work.
Plasterers earn their wings in two different ways. Some learn by watching others and develop skills suited for straightforward jobs. The better ones hold qualifications like the City & Guilds (6217) Certificate in Basic Construction Skills (Plastering). It’s important to understand the difference in qualifications when assessing the quality of Plastering Quotes. This information is provided by Mr-Skill.
Tags: apply, ceiling, City and Guilds, cornice, damage, decorator, dry, dry lining, dry wall, drywall, exterior, fibrous, find a plasterer, interior, internal, mix, outside, painter, pebble dash, plaster, plasterer, plasterers in london, plastering quote, plasterwork, rose, solid, wall, wet
Posted in Plastering & Drywall | Comments Off
Posted in Carpentry & Joinery on Jan 25
I was in an antique shop in London the other day, admiring some really lovely pieces of old furniture and wondering how they got their finishes so smooth. Later in the day I met up with an old London Carpenter friend of mine in a listed City pub. As he ran his hand over the gleaming wooden counter, he let a few trade-secrets slip.
• Wait for a windless day while you prepare a suitable work-place out of the sun
• Assuming you’ve prepared everything properly and that your work-piece is completely dry, give the varnish a proper stir for at least five minutes if not longer.
• Strain the varnish through a silk stocking to get rid of any remaining lumps.
• If you feel a call of nature coming on take that break now, as you are going to work through to completion.
• Moisten the best quality brush you can lay your hands on in the cleaning solvent the varnish manufacturer recommends (this prevents the brush from clogging up).
•  Apply the varnish evenly with a series of long firm overlapping strokes. Do not return to touch-up. Never scrape the brush across the container – it is this action that creates the bubbles.
• Don’t fiddle with your work afterwards and mess it up. Allow it to dry naturally for twenty-four hours before checking in an inconspicuous place.
That sounds like good enough advice for me and I might no longer need to Find a Carpenter for those smaller jobs. However if I decide to re-varnish the wooden staircase in my home the wife is always nagging me about, I think I’ll rather go for Carpentry Quotes on Mr-Skill instead. It’s just so much easier, and inexpensive allowing for the savings on my own time.
Tags: antique, apply, brush, bubble, carpenter, carpentry quotes, clog, container, dry, fiddle, find a carpenter, finish, furniture, london carpenter, lump, moisten, naturally, overlap, prepare, scrape, secret, smooth, solvent, stir, stocking, strain, stroke, sun, tip, touch up, varnish, wind, wood
Posted in Carpentry & Joinery | Comments Off
Posted in Electrical Work on Jan 23
The last thing you need in any circuit is a dry joint, by which I mean two wires twisted round each other or even worse. In a home, this can cause the power to keep on tripping, while in the low voltage world the result is a random electronic fault.
 From time-to-time it’s necessary to get a soldering-iron out. Before you rush around looking for an Electrician Quote it might just be possible to do the job yourself.
• Preparation Clean both parts that you are planning to solder into a joint. Hardened, damaged wire is a recipe for disaster so make sure everything is shiny new by stripping off a fresh end. While at it, remove any vestiges of solder if you’re repairing an existing joint. That’s because solder does not stick to itself at all well when not fresh.
• Tinning Heat each surface in turn until it just melts a bead of solder. Work this back and forth until you see a little amber liquid appear. That’s the tinning that’s the meat in a good joint. It will be HOT. Allow the material  to cool down naturally before you touch it with your hands.
• Soldering Mount the larger of the pieces to be joined securely in a vice. Heat up its surface until solder melts instantly on it. Place the other tinned piece in the pool of solder, remove the soldering iron, and wait until the surface of the melted solder goes slightly dull. Allow the joint, which will be HOT to cool naturally.
If you have a soldering iron that’s in good order and you have the time, you don’t really need to Find an Electrician, do you? But beware one thing, and that’s a bad joint. A London Electrician I know tests his apprentices’ work by seeing whether he can pull it apart.
Tags: bead, circuit, clean, cool, dry, electric, electrician quote, electronic, find an electrician, flux, fresh, heat, hot, joint, london electrician, melt, preparation, remove, solder, solder iron, strip, tin, tinned, vice, wire
Posted in Electrical Work | Comments Off
Posted in Tiling & Flooring on Dec 14
For some peculiar reason that I don’t quite understand, bathrooms in UK homes are seldom fully tiled. Personally I think developers are being mean. How much can it cost to Find a Tiler to extend a run of wall tiles once the levels have been set?
Here’s a neat way to integrate a mirror on a painted wall with tiles elsewhere in the room.  Let your imagination loose here. The choices are endless!
- Buy the mirror and install it plumb and level with concealed mounts. Obtain sufficient wall tiles of a suitable finish and have them cut to size. If need be, you could get a Tiling Quote to have the cutting done.
- Mark out the area around the mirror where the tiles will go, and mask it off for at least the width of the tiles. Mask the frame of the mirror carefully too.
- Apply a layer of tile-keying liquid between the two runs of masking tape. Attach a batten to the wall to support the bottom run of tiles.
- Glue on the bottom run of tiles using pre-mix tile cement. Allow this to dry for twenty-four hours.
 Return the next day to complete the job, making sure the tiling spacers keep the joints between the tiles neat.
TIP A London Tiler I know well uses epoxy to secure the tiles. This may add a little to the cost, but at least he can complete the tiling on a single day, and get the money back that way.
- After waiting another day for the glue to dry properly, remove the batten and the masking tape, grout the tiles and tidy up the wall.
Little details like this can make all the difference, and add DIY pleasure to a weekend. Aren’t you glad you found a handy website like this? What’s more, you can Find Tradesmen for all larger jobs right here. And it will not cost you a single penny more!
Tags: bathroom, batten, cement, cut, dry, eopxy, extend, find a tiler, frame, key, level, london tiler, mark, mask, masking tape, mirror, mount, plumb, pre mix, quote, set, spacer, tile, tiled, tiling quote, wall, width
Posted in Tiling & Flooring | Comments Off
Remember the days of central heating radiators when you got just one choice like porridge in a boarding house. Great lumbering cast-iron things they were, and broad enough to support two schoolboy bums chilled from walking across frozen fields to get to school.  That’s all changed thank heavens. These days, when you get Plumbing Quotes on Mr-Skill you get flooded with designer brochures too.
Even the old fashioned cast-iron radiator has become a thing of beauty with inboard towel-drying rail incorporated in the design. Stainless steel ones are even more alluring thanks to the opportunities this metal offers. These days you can have bars that run horizontally too. Perfect for drying the washing on a rainy day!
Lightweight aluminium offers unlimited opportunities for air-circulation through the fins, although I still doubt the thermal properties of the alloy metal. Flat steel-panel radiators are ideal for commercial applications, although useless for drying out a wet coat. And then there are the tubular ones – just perfect for warming seats in cold stone parish churches. You just need to Find a Plumber to install them as a gift of love!
 Designer radiators are the ones I really love though. Modern metal-working techniques permit a stunning collection of gently flowing tubes and angles. These days more than a few London Plumbers are full of creative ideas. Your friends could even think that yours are pure decoration, and that there’s under-floor heating concealed elsewhere in the room.
I really love these great ideas for modernising old trusted friends like central heating radiators, as much as I love having Mr-Skill to help me Find a Reliable Plumber too. One last thought. I doubt that all the modern contraptions I described would take the weight of two healthy schoolboys … this one should though.
Tags: air circulation, alloy, aluminium, bars, brochure, cast iron, central, design, designer, dry, fin, find a plumber, heating, horizontal, london plumbers, panel, plumbing quotes, radiator, rail, stainless, steel, towel, tubular
Posted in Plumbing, Heating & Gas | Comments Off
Posted in Bricklaying on Nov 25
We get queries from time to time from homeowners concerned about the efflorescence on their walls. Sometimes these walls have been rendered, while at other times they are raw masonry. In all cases the powder is caused by leeching salts contained in the raw materials. So there’s little point in trying to Find the Builder who built the wall –  although you could help avoid the problem by employing a professional bricklayer, such as those whose services we advertise here.
The ground salts are contained in natural products like sand, clay and stone. When water penetrates the material it carries the salts out to the surface. There the water evaporates leaving the characteristic white deposit behind. This can largely be avoided by preventing water intrusion and applying a surface sealer. When you get Bricklaying Quotes from Mr-Skill, you should discuss such matters and agree solutions.
• Brushing the efflorescence away is only a temporary solution, although theoretically all the ground salt will leech out in time.
• The permanent solution lies in preventing water from entering the material in the first place. If it is  intruding from the outside, then this is relatively easily cured. If the wall is a retaining one though then a big job lies ahead as every London Builder knows. That’s because a leak is only stopped at its source, and that’s behind the wall!
• If you are lucky, then the problem is the result of a permeable surface on the weather side. The solution in this case is to allow the wall to dry out, thoroughly brush the surface clean, and then apply a proprietary clear sealer.
The Bricklayers advertising on Mr-Skill are properly trained and know how to mitigate against irritating efflorescence. Their rates are generally lower too, because they compete among themselves for work. There is no charge for requesting quotes from us and no obligation to accept them either. Doesn’t that sound like the perfect consumer-driven solution you’ve been looking for?
Tags: bricklaying quotes, brush, clay, clean, deposit, dry, efflorescence, enter, evaporate, find a bricklayer, ground, intrusion, leech, london bricklayer, masonry, natural, outside, penetrate, permeable, powder, prevent, render, retain, salt, sand, seal, stone, wall, water, white
Posted in Bricklaying | Comments Off
I never cease to be amazed at the variety of bathroom accessories available at hardware stores across the UK these days. Every one of these has at least one fixing hole – if I got that contract I doubt I’d ever look back. Many folk are nervous about drilling through ceramic tiles though, because the consequences of cracking one can be quite expensive.
And so they try alternatives like two-sided tape and contact glue. Unfortunately these never work properly because ceramic tiles are highly glazed. Worse still, the accessories come loose, and chip even more expensive fittings when they come crashing down. If you are handy you don’t need to Find a Bathroom Fitter – you just need the right tools and your brain switched on.
• When working above a drainage point like a washbasin or a toilet, insert the plug or lower the seat. Lay down a dust-sheet to make cleaning up afterwards easier too.
HINT – Ceramic tile and masonry dust can permanently stain moist grout, so make sure your work area is dry.
• Gently tap the tile where you intend to drill the hole with something metallic that’s also light. If you hear a hollow sound there’s airspace between the glue. London Bathroom  Fitting Firms train their staff to look for another fixing point when they find this, because tiles break easily over hollows.
• Make a clear mark on the tile where the hole must go with a laundry marker. Make a cross over it with transparent tape that does not have a shiny finish. Tap the tape gently and repeatedly with a new centre punch, until you have scored the ceramic finish beneath it.
• Drill through the hole using a specialist drill bit and an electric drill set off-hammer. Once you are through the glaze you can drill into the tile and wall more quickly. Tidy up the mess, wipe things clean, and you’re good to go!
Mr-Skill is a virtual market place where customers and skilled tradespeople meet. It’s free to the general public, and bids can be up to 30% below general market rates. Click on this link – get Cheap Bathroom Fitting Quotes for your postcode right now!
Tags: accesory, accessories, bathroom, bathroom fitting quotes, bit, break, ceramic, chip, clean, crack, drain, drill, dry, dust, find a bathroom fitter, fix, gently, glaze, glue, harware, hole, london bathroom fitting, mark, masonry, punch, sheet, tap, tape, tile, tool, wall, wipe
Posted in Handyman Services, Kitchen Fitting, Painting & Decorating | Comments Off
|
Subscribe to our RSS Feed