| |
Posts Tagged ‘pressure<’
There’s nothing quite as irritating as water hammering in pipes, especially when you’re trying to sleep and someone gets up to use the loo. Unfortunately water is one of those things that has its own mind. There are however ways that you can control it,  and you may not even need to Find a Plumber if you read further.
When you turn off a water tap that’s under pressure (usually the cold one), the water suddenly stops flowing as it comes up against the valve. It pushes back against the water that’s still on its way. The result’s a slight collision between opposing forces.
The energy that’s released transmits to the pipes themselves, which respond by reverberating. Normally, you don’t hear the slight sound that results. However, when the pipes are hanging loose they bang about, and that’s the noise we call a water hammer. There are two ways to sort the problem out. Fix it completely, or manage it.
- Solve the problem at its source – Obtain a Plumbing Quote on Mr-Skill to install a water
 hammer arrestor. This is in effect a shock-absorber that absorbs the impact and eliminates the root cause. The picture above is of arrestors attached to dish-washer inlet pipes. London Plumbers often install these in older homes, where loose pipes are bricked up behind rendering.
- Eliminate the consequences – Take a look at the picture opposite. It’s typical of what you might find when you look. Can you see how many pipes are hanging loose? What an opportunity for a water hammer. Your most likely culprit though is an unsupported run of pipe across the ceiling. Find it, secure it, solve the problem.
These water hammer solutions come to you with the compliments of Mr-Skill, the website where you find the perfect solution to every home repair. Don’t take a chance and hire an unknown trades person off the street. We personally investigate the ones we recommend.
Tags: arrestor, bang, control, find, find a plumber, fix, hammer, knock, london plumbers, loose, pipe, plumbing quote, pressure, reverberate, secure, solve, transmit, water, water hammer
Posted in Plumbing, Heating & Gas | Comments Off
I find it surprising how so many people put so little thought into the subject of their taps, when they do a bathroom upgrade. After all, these are essential user-interface points, and they must feel right. I’ve heard that some London Bathroom Fitting Firms insist their clients choose their taps themselves, and then design the rest around them.
While this does sound a bit bizarre, it also makes a lot of sense. Many bathroom fitters don’t specify the  taps included in their Bath Fitting Quotes, and could be tempted to dumb designs down if they run over budget. The first thing is to check your relative water pressure – any plumber could do this for you – after which you’re ready to go out shopping.
- Old-fashioned Pillar Taps add a retro feel, and are perfect for twiddling in the bath with toes.
- Mixer Taps are simpler because there is a single outlet and you can feel whether the temperature adjustment is right
- If your cold and hot water pressure is unbalanced go for Dual Flow Mixer Taps instead.
- Monoblocks take things a stage further because now you only have a single leaver you can pre-set.
- If you have an in-bath shower, buy a Shower Mixer that allows you to divert the water up or down.
 The next step is to choose the design itself, which is largely a matter of personal taste. Brass-effect taps provide an invitingly warm effect reminiscent of graceful days. Shiny Chrome is hard to keep looking clean. Matt or satin finishes are all in vogue, and appear likely to remain that way.
Once you’ve made your decision – but don’t buy just yet, you never know – you can Find a Bathroom Fitter on Mr-Skill you can engage in comfort. Don’t take a chance by hiring a possible cowboy off the street. Shop with confidence on Our Website.
Tags: bath fitting quote, bathroom, brass, budget, choose, chrome, design, dual flow, feel, find a bathroom fitter, finish, london bathroom fitting firm, matt, mixer, monobloc, monoblock, pillar, pressure, satin, shower, specify, tap, water
Posted in Other Craftsman Services | Comments Off
While replacing glass in a UPVC door (or window) is something professionals usually do, there may be times when you have to do the job yourself – like over the Christmas break.  You could do the job yourself provided you can lay your hands on a suitable pane of glass, but do wear gloves and work carefully. At other times it makes far more sense to Find a Window Fitter on Mr-Skill.
- Examine the door frame around the damaged glass to determine from which side it was fitted. One side will have an unbroken line over a strip of rubber. On the other side there will be four pieces of beading that clip in to hold the glass.
- Take up a sharp putty knife or paint scraper and work it under a bottom or a side piece of bead. Hold your other hand out of the way in case the tool slips. Carefully prise out the bottom and side beads, except the top one which will still be holding the glass in place.
 Have an assistant hold the glass in the door frame while you take out the top bead. Hold the pane on both sides while you gently lower it out. Be careful! Wear gloves. The edges will be razor sharp!
- Install the replacement pane in the reverse order, taking care not to crack the glass by applying too much pressure. London Window Fitters often use the trick of applying a little dishwashing soap to the recess in the window frame, when pressing in the final bead.
Under normal circumstances we would recommend that you get Window Fitting Quotes instead and perhaps on Mr-Skill too. That’s because you run the risk of injuring yourself, if for no other reason than that the job may be a little bit unfamiliar to you.
Tags: bead, beading, bottom, broken, clip, crack, damage, dishwash, door, find a window fitter, fit, frame, glass, harm, injure, install, knife, london window fitter, pane, pressure, prise, quadrant, replace, rubber, scraper, sheet, side, soap, strip, top, uPVC, window, window fitting quote(s)
Posted in Window & Door Fitting | Comments Off
 The first thing to remember is that cold-water pressure is relative, but that yours should be the same as both your neighbours. If all three homes have poor water pressure then the problem lies with council delivery and you should speak to them. If the problem is restricted just to you though, then you have a stoppage somewhere in your home. Here is how to track the problem down.
o Is the pressure low at every tap, or just at one? If just at one, then you most likely have a faulty tap, or hopefully just a damaged washer. Tap washers must be changed as soon as possible to avoid damaging the tap itself. Try changing yours right now. If this did not solve the problem, then Find a Plumber to Replace the Tap for You on Mr-Skill instead.
o If the pressure is low on several taps but not at all of them, then you might have a stoppage in a line somewhere. This is likely to be a valve in the line concerned that is not set fully open. My mate from <a href="http://www.mr- skill.co.uk/plumbing-heating-and-gas/”>Reliable Plumbers London always opens a valve fully and then closes it back a quarter turn. This is so he can work it back and forth if it gets sticky later.
o If the pressure is low throughout the house, then the main supply valve at the water meter could be partly closed. If all else has failed, then this could solve the problem easily. Remember not to leave it fully open either please.
If none of the above suggestions works a trick then I am afraid that you have a partial blockage in a pipe somewhere. You need to Find a Friendly Plumber to help you out on Mr-Skill, before you end up with a pipe burst. You will find plenty more helpful advice from the folk at Mr-Skill on this blog.
Tags: blockage, change a washer, council, find a plumber, line, meter, neighbour, open, pipe, plumber london, plumber quote, plumbing job london, plumbing quote, pressure, sticky, stoppage, tap, valve, washer, water, water meter
Posted in Plumbing, Heating & Gas | Comments Off
|
Subscribe to our RSS Feed