| |
Posts Tagged ‘replace<’
Posted in Tiling & Flooring on Feb 27
First you notice that the grout between the tiles has begun to crack. You wonder whether it’s time to Find a Tiler. After that, the grout starts going darker in one spot. Finally, when you tread on a tile, it rocks slightly as the moisture squishes out.
 Fortunately, this is not the end of the world! The good news is that the tile is loose and will be easy to remove. After that, you can have a Plumber in to fix the leak, and perhaps even replace the tile afterwards yourself.
- Avoid your first reaction to lever out the tile. Chances are that you will chip it, and where on earth will you find a replacement one? One London Tiler I know wets the loose tile generously, and then uses a toilet plunger to create a vacuum and gently ease it out. Try it. You could just be pleasantly surprised!
- Depending on how bad the leak is, you may need to turn the water off. If the water is not bubbling out from where you removed the first tile, you may need to chase the leak by removing several more. This is easy when you gently tap a paint scraper
 underneath the middle of the tile, because the mortar will be water-logged.
- Find a Plumber on Mr-Skill to repair the leak. Then wait patiently until the hole the plumber left behind has dried out completely. After that, back-fill it with a strong mix of mortar, and get a Tiling Quote to put the tiles back and re-grout. If you do the job yourself, use an epoxy as there will be insufficient space for tile cement except where the plumber made the hole.
This information comes to you with best wishes of Mr-Skill, that friendly website where you can find every service that you need. These services include electricians, builders, plasterers, carpenters, gardeners and a whole host more besides. The service costs you nothing, and they are all rated too.
Tags: back fill, chip, crack, dark, dry, epoxy, find a plumber, find a tiler, grout, lever, london tiler, loose, moisture, mortar, paint scraper, plumber, plunger, rated, remove, replace, rock, scraper, service, tap, tile, tiling quote, vacuum, water
Posted in Tiling & Flooring | Comments Off
Posted in Plastering & Drywall on Feb 01
Damp is an on-going problem in many homes in Britain, and that’s not just in the older ones either. Water, especially when forced by wind can find its way inside an outside wall through the tiniest of cracks. After the leak is fixed, it’s time to Find a Plasterer to fix the evidence that alerted us to the damp in the first place.
The Problem
The water has leached the cement away leaving weakened plaster that will eventually come off. The only solution is to hack it out and replace it. You have a choice, though. You could Ask Mr-Skill to Arrange a Plaster Quote, or you could have a go at it yourself.
 Repair Stage One
You have to get rid of the damaged plaster at least a foot above any visible damage or residual salts. If the damp was low down, then you must in any case remove the plaster to three feet above floor level. Brush away every grain of loose material. Complete the job with a vacuum cleaner – you may wish to do this when the wife is out shopping.
Repair Stage Two
This is a tip a London Plasterer taught me years ago. Put on a pair of disposable latex gloves. Make a slurry of cement powder and water with a cup of bonding liquid added – the final consistency should be like runny porridge. Brush this firmly over the space where the old plaster came out. This will allow the new plaster to adhere properly. Wash your hands and tools immediately. Allow the slurry to dry for a day.
Repair Stage Three
Make up a stiff plaster mix of 3-Parts sand to 1-Part cement. Apply this with a wide paint scraper or steel float across the entire surface roughly, and leave it alone for two hours to set. Apply a fresh mix of plaster that stands just proud of the surface. Work this off with a straight edge later the same day.  Leave the job to cure for a week.
Repair Stage Four
Apply a moist mix of Polyfilla over the entire surface. When it’s totally dry and the surface has gone a little powdery, finish the job off with an a sanding block or orbital sander, using medium-grit paper. After that, you are ready to decorate!
That’s all very well in theory, but do you really have the time to spend on this? If not, that’s where Mr-Skill comes in. We provide a matching service between customers and tradespeople. Unlike some others, we don’t add a penny to the cost of jobs.
Tags: adhere, bond, brush, cement, clean, consistency, crack, cure, damage, damp, dry, dust, exterior, find a plasterer, float, get rid of, glove, grit, hack, london plasterer, mix, orbital, outside, paint scraper, plaster, plaster quote, polyfilla, powder, remove, replace, salt, sand, scraper, set, slurry, stick, straight edge, tip, wall, water
Posted in Plastering & Drywall | Comments Off
Posted in Handyman Services on Jan 12
I’ve noticed a tendency these days for estate agents to describe run-down properties as handyman delights. Perhaps the implication is that there are a few fun-things to attend to over several leisurely weekends? Some properties I’ve viewed recently reveal that they require considerably more attention than just that.
If you’re in the same position then you’re certainly not alone. The following are jobs currently posted on Mr-Skill and  awaiting Handyman Quotes:
- Fixing Garden Panels Securely. The fences we put up around our yards are often cheap and nasty, and the poles are seldom properly concreted in. This one’s perfect for a handyman – you don’t need more advanced skills here.
- Letter Box Replacement. This one’s straightforward too and I’m sure that Mr-Skill will Find a Handyman to do it pretty soon. It seems the front flap’s snapped off. Pretty urgent I would have thought. After all we’re in the middle of winter in case you hadn’t noticed.
- Attach Bathroom Fittings. I find it remarkable that developers no longer supply even a basic toilet roll-holder and simple soap dish. How mean is that?
 They make a fortune, and the comment “we thought we’d let you choose” cuts no ice with me at all. Their show houses certainly have bathroom fittings in abundance.
- Sand Down a Wooden Floor. This is a fairly easy task when you have the right tools. In fact I know a London Handyman who makes his living that way in older houses. I wouldn’t bother with a carpenter here – an experienced handyman is quite capable of the job.
- Remove a Fallen Tree. This one seems displaced to me, and perhaps belongs better under gardening and landscaping? I doubt the average handyman has the required power saws, or a trailer to remove the cuttings for that matter either.
When you think about it, there are an amazing number of jobs a Handyman could do around the house. The problem is that some so-called handymen are downright awful. That’s where the Website Mr-Skill makes such a difference. Our handymen are rated by their customers, so you can see what you are getting before you buy.
Tags: bathroom, cheap, concrete, cutting, fence, find a handyman, fitting, flap, floor, Garden, handyman, handyman quotes, holder, job, letter box, london handyman, replace, run down, sand, saw, soap, toilet roll, trailer, wood
Posted in Handyman Services | Comments Off
While replacing glass in a UPVC door (or window) is something professionals usually do, there may be times when you have to do the job yourself – like over the Christmas break.  You could do the job yourself provided you can lay your hands on a suitable pane of glass, but do wear gloves and work carefully. At other times it makes far more sense to Find a Window Fitter on Mr-Skill.
- Examine the door frame around the damaged glass to determine from which side it was fitted. One side will have an unbroken line over a strip of rubber. On the other side there will be four pieces of beading that clip in to hold the glass.
- Take up a sharp putty knife or paint scraper and work it under a bottom or a side piece of bead. Hold your other hand out of the way in case the tool slips. Carefully prise out the bottom and side beads, except the top one which will still be holding the glass in place.
 Have an assistant hold the glass in the door frame while you take out the top bead. Hold the pane on both sides while you gently lower it out. Be careful! Wear gloves. The edges will be razor sharp!
- Install the replacement pane in the reverse order, taking care not to crack the glass by applying too much pressure. London Window Fitters often use the trick of applying a little dishwashing soap to the recess in the window frame, when pressing in the final bead.
Under normal circumstances we would recommend that you get Window Fitting Quotes instead and perhaps on Mr-Skill too. That’s because you run the risk of injuring yourself, if for no other reason than that the job may be a little bit unfamiliar to you.
Tags: bead, beading, bottom, broken, clip, crack, damage, dishwash, door, find a window fitter, fit, frame, glass, harm, injure, install, knife, london window fitter, pane, pressure, prise, quadrant, replace, rubber, scraper, sheet, side, soap, strip, top, uPVC, window, window fitting quote(s)
Posted in Window & Door Fitting | Comments Off
Posted in Plastering & Drywall on Dec 05
After a builder installs a window, or a window fitter replaces one, there’s usually a gap between the window and the wall on either side. Experienced London Plasterers know how to close this in with rendering. In this article though, we focus on a more modern  technique that uses strips of plasterboard instead
This job is nominally within the target range of anybody who is good with their hands. It does require a fair degree of patience though, and those with delicate chests might prefer to avoid doing it on account of dust. Should you decide to go ahead yourself, then these are the essential steps:
- Cut sufficient strips of plasterboard to complete the job. lf the gap is deep, consider using several layers of board as opposed to balancing a single one on large blobs of glue, and being able to finish off the job immediately. When discussing Plastering Quotes you receive on Mr-Skill with bidders, find out how they propose to the job too.
- Apply proprietary dry-wall adhesive to the brickwork on one side of the window. Push a
 plasterboard strip into place using a square edge and spirit level to keep it true.
- Add further layers of strips using the same proprietary dry-wall adhesive, until you have built up to the desired level and flush with the window frame.
- Repeat the process on the other side. Now you can add the angle beading where your work interfaces with the wall, tidy up generally and redecorate.
Of course the third method would be to Find a Plasterer on Mr-Skill, and get on with something else that you’d prefer to do instead. We select contractors with extra-special care, to make sure that each and every trades person we introduce is the best.
To benefit from their expertise and brilliantly lower prices, all you need to do is to Post Your Job for free!
Tags: adhesive, angle, angle beading, bead, brickwork, builder, decorate, dust, find a plasterer, finish, flush, gap, glue, layer, level, london plasterers, new, patience, plaster board, plasterboard, plastering quote, process, push, repeat, replace, square, strip, tidy, wall, window, window fitter
Posted in Plastering & Drywall | Comments Off
Posted in Carpentry & Joinery on Nov 24
While parents may still find them handy for tracking teenagers in and out at night, the truth is that a squeaking floor is an irritating thing that is literally crying out for your attention. Before you look for cost-effective Carpenters Quotes on Mr-Skill, you may like to try out these handy ideas first.
 Floor boards creak for one of three reasons, and these are some of the things you can do to fix them – possibly by yourself – once you have walked the floor and found the source:
1. They are incorrectly fitted and rubbing up against each other. Pour a little talcum powder into the crack and work it in by pressing up and down with your foot. If this works, repeat the treatment regularly.
2. The nails holding them down have worked loose. If at all possible, remove the nails completely and replace them with wood screws. If not, you may have to fit new screws separately, hammer the old nails in as best you can, and fill the nail heads with filler. Start with two screws, each towards the outer edge of the board, remembering to countersink them. Only add a middle one if necessary.
3.  The floor support is inadequate. This is a major job and you need to Find a Carpenter on Mr-Skill to do the job for you. They will remove a section of floor boards, add additional supporting battens and re-lay the floor. If done correctly by a professional there is no reason why the job will not work. Done incorrectly by a cowboy though, and it could cost you the floor.
There are Experts in London Carpentry on Mr-Skill, and specialist carpenters working in almost every other United Kingdom postcode too. When you Hire a Skilful Tradesman here, you not only get one with all the correct papers. You also get to save pounds off normal market rates.
Tags: add, batten, board, carpenters quotes, countersink, creak, fill, filler, find a carpenter, floor, floorboard, hammer, incorrect, lay, london carpentry, loose, nail, paper, powder, professional, rate, reason, relay, remove, replace, rub, save, screw, section, specialist, squeak, talcum, work
Posted in Carpentry & Joinery | Comments Off
Posted in Tiling & Flooring on Nov 17
If you’ve got tiled floors, tiled splash backs and tiled walls in your home (and we all have these in abundance these days) then the chances are that the grout is looking grotty, unless, that is, you’ve kept your hand to it. Why is this? It’s simple really. As every London Tiler knows, grout is a cement product and cement absorbs grease and grime.
In the bathroom, the dirt is usually mould from steam, soap accumulation and what’s best described as body residues.  Wipe wet walls and glass doors regularly and things will stay under control. Ignore this advice, and in a month or two your bathroom will start looking yucky, and it’s time for elbow grease and chemicals.
You’ll find mildew in the kitchen too, and food spills trafficked by feet across the floor. Some ingredients such as saffron and tomato sauce have amazing staining properties as well as legendary tastes, and you should wipe them right away. If you don’t, suddenly you’ll notice that cute has left your kitchen, and that it’s time to start cleaning up again.
• If things are not all that bad yet, you can try cleaning off the grout with either vinegar, baking soda or sugar soap. A steam cleaner can also help blast the dirt away but watch out for the mess. Never use ammonia-based cleaners on white grout, because they turn it yellow over time.
•  Didn’t work? Then try commercial cleaners like Mr Clean or Lysol, making sure you wash them away completely. Be careful of using corrosive products that can make your hands tingle – especially if your waste water ends up in a soak away.
• Still got problems? Then I’m afraid you need to Find a Tiler to rake out the offending grout and replace it with a matching one. Be careful of trying this yourself though – it’s not difficult to chip an exposed tile edge and you may not have a spare.
We have a comprehensive database of Tilers on Mr-Skill serving every UK postcode, and we can arrange several Tilers’ Quotes for you in just a few hours. Their rates will be better than competitive, and we don’t charge customers for our service. Moreover, our other customers have already rated them for quality.
Tags: absorb, baking soda, body, cement, chemicals, chip, clean, corrosive, find a tiler, floor, food, grout, london tiling company, match, mildew, rake, replace, residue, soak, soap, spill, splash, steam, sugar soap, tile, tilers quotes, track, vinegar, wall, wipe
Posted in Tiling & Flooring | Comments Off
Posted in Carpentry & Joinery on Nov 08
Bedroom fitters seem to find it necessary to install cupboards from the wall to ceiling. While this makes sense in terms of managing the dust on top, customers often end up with storage space that looks more like the inside of a church steeple. The solution? Add a space below for storing shoes, or above for keeping what almost inevitably turns out to be junk.
 I personally don’t have much time for using the plastic shelf blocks that seem all the rage these days. That’s because they involve point contact and it’s difficult to get them aligned perfectly. Moreover, in these times of chipboard everything, an overloaded shelf can easily come crashing down.
The following is what Professional London Carpenters still prefer to do:
• Remove the cupboard doors for ease of access and to avoid straining hinges. Measure the internal depth of the cupboard from front to back at both left and right. While you’re at it, measure the cupboard internally from left to right too. Enter the information on a drawing, because in all the years of providing Carpentry Quotes I have seldom come across a cupboard that’s perfectly square.
• Ask the hardware store to cut a shelf to size and to cut battens to support it on the left and right too. Make sure they also supply half-a-dozen screws of the appropriate length.
•  Pre-drill the battens in the middle and towards either end. Fix the first one in the middle only and set it horizontal with a spirit level. Draw a pencil line along the bottom edge and fit the other two screws accordingly.
• Measure from the top or bottom of the cupboard to determine where the second batten should go. Screw it into place, again just using the middle hole. Test fit the shelf in place. It should be level and fit snugly so you can complete the installation and replace the doors. If not, you may need to make adjustments.
You could also save yourself a heap of trouble and get Highly Competitive Carpentry Quotes on Mr-Skill instead. We have carpenters at every UK postcode. They’re on standby to fit that shelf for you, and much more.
Tags: battem, bedroom, block, bottom, carpentry quotes, chipboard, complete, cupboard, cut, door, drill, dust, find a carpenter, fit, hinge, horizontal, length, london carpenters, measure, plastic, remove, replace, screw, shelf, shoe, size, snug, spirit level, square, storage, strain, support, test, top, vertical, weight
Posted in Carpentry & Joinery | Comments Off
Posted in Locksmith on Nov 07
There’s nothing quite as unnerving as arriving home from holiday, and finding you’ve either lost your key or the front door lock refuses to budge. This unfortunately boils down to a lack of care or just stupidity. I can say that, because I’ve been guilty of these oversights myself when I was younger.
 Lost Keys – The solution is as simple as people’s failure follow it is incredulous. Leave a spare set of keys with a good friend you trust, so they can visit your home from time to time too. That way, you may never need to Find a Locksmith at such an inconvenient hour.
Jammed Locks – It’s a funny old thing, isn’t it? We update our ant-virus databases and we even sometimes mow our garden lawns. Yet we leave our essential door and window locks to take care of themselves completely, when all you need to do is the following:
• Lubricate all your exterior door locks with a puff of graphite powder (not oil because that will attract the dirt and dust). Lock and unlock them several times to work the lubricant in. If the lock is exposed to the elements and seldom used, consider taping over the outside keyhole with a piece of weatherproof tape to keep the moisture out.
•  The advice of every London Locksmith and all others lock repairers too is to take action as soon as a lock starts giving trouble. If you can open the door or window you could change the lock yourself. At the least you could possibly avoid paying overtime rates.
• Inspect your keys monthly for signs of damage, and never, ever use worn ones. That’s because a broken piece of key can be impossible to remove, necessitating an expensive repair.
Whatever else you do please do not overlook the need to maintain your locks. Did we mention you can get Locksmith Quotes on Mr-Skill too? You’ll find the rates more than competitive and our service exemplary. Isn’t that good to know. Remember that in times of trouble we’re here for you.
Tags: break, broken, budge, care, change, damage, door, element, find a locksmith, friend, graphite, inspect, jam, key, lock, locksmith quotes, london locksmith, lose, lost, lubricate, maintain, moisture, oil, powder, rate, remove, replace, solution, spare, stuck, tape, weather, window, work
Posted in Locksmith | Comments Off
Posted in Tiling & Flooring on Oct 21
Funny, isn’t it, how fashions keep on going round and round. All that’s as true of building materials as it is of clothes. The difference is that your home is going to have to wear its finishes for far longer than you are going to hang on to your hat. For this reason it’s best to know what you are looking for before you get your Tiling Quotes.
 Did I mention that I went to school with a London Tiler? Well he wasn’t a tiler then, but he did become one good enough to successfully start his own flooring firm. This was the advice he gave when asked:
• Stick to natural materials wherever possible. This is because they are timeless and you can always find an acceptable replacement, even if a tile breaks after fifty years.
• Travertine is often beautifully marked and coloured having been paid down by rivers over centuries, and is soft and easy to work with. In the fancy shops it is also called onyx and alabaster.
• Limestone is another sedimentary rock primarily white or light coloured, but also tinted by small impurities. It is often used in commercial developments where the varying thicknesses are an architectural asset.
• Slate is traditionally used for flooring, although new techniques have seen it applied to walls too. It is extremely durable making it ideal for outside use. However quality is unpredictably varied.
•  Marble is valued for its mirror finish after polishing, and has been used for cladding buildings for thousands of years. It is probably the most expensive of all the options, and the most copied by ceramic tile manufacturers.
• Sandstone provides an attractive varied finish on feature walls, although good effect is often only achieved by hand-sorting tiles. It is brittle and unsuitable for floors.
Now that you have made a choice why not Find a Tiler on Mr-Skill right away? You will have range of choices when you shop through us. You may even expect savings of up to 30% on labour against normal rates thanks to our buying power.
Tags: brittle, Building, colour, durable, easy, effect, expensive, fashion, find a floor contractor, floor, light, limestone, london tiler, marble, mark, natural, outside, polish, replace, sandstone, sedement, slate, soft, thick, tile, tiling quotes, travertine, vary, wall, white, work
Posted in Tiling & Flooring | Comments Off
|
Subscribe to our RSS Feed