| |
Posts Tagged ‘test<’
Posted in Electrical Work on Mar 06
Thankfully as winter starts to move on, now is a good time to check that your outside lights are in good working order. Some of the work is easy and safe enough to do yourself. Changing a bulb is a good example, as is cleaning the glass in the light fitting. If the light is not working though, you would be better off using a qualified electrician to solve the problem. Wiring and switching is too dangerous for an unqualified person to work on. Rather check with Mr Skill, find a qualified electrician, and ask them for an electrical quote.
- Make sure that the light switch is in the “off” position. Better still; isolate the light circuit on your electrical board.
- Have a stepladder handy should you need to reach up to the light fitting.
- You may have to remove a piece of glass to access the bulb.
- Wipe the interior of the light fitting with a clean rag.
- Now, remove the old bulb. Be careful, it might be hot.
- Replace the bulb with a correctly-rated new one.
- London electricians always recommend using energy-efficient bulbs. They may cost more, but they will last much longer and therefore require less maintenance.
- Refit the glass panel, having cleaned the surface first.
- Test the new bulb once you have installed it, by flicking the light switch to “on” after you re-set the distribution board.
- Never replace a bulb with a wattage-rating higher than the fitting manufacturers recommended maximum.
If, after having been through the above steps the bulb still does not light up when you switch it on, find an electrician by clicking on Mr Skill.
It’s all about horses for courses and being smart. You wouldn’t consider using a plumber to fix your own car, so be wary of trying to fix your own electrical problems!
Tags: bulb, check, circuit, cloth, cost, efficient, electrical board, electrical quote, energy, find an electrician, fitting, glass, ladder, light, london electricians, maintenance, off, on, rag, rate, screw, switch, test, wipe, wiring
Posted in Electrical Work | Comments Off
With winter upon us – and a freezing one at that – many people across the United Kingdom are experiencing problems with their guttering. These can include gutters filled with ice collapsing, and nowhere for water to go when the thaw comes. Is it possible to prevent this? Well, we can’t prevent a blizzard, but we can Find a Roofer to take preventative action for us.
 These are some of the things worth considering when you are busy getting Roofing Quotes.
• When snow gathers on a roof it should thaw gradually without causing problems. But, if you have heat build-up above your ceiling then it might melt all at once, blocking gutters that then freeze up. Two things to do. Check your ceiling insulation, and make there’s provision for any heat to escape.
• Ensure the water entering your gutters can flow smoothly through the down-pipes. This means cleaning them thoroughly twice a year (before and after winter) and testing them from time to time.
• Matt, my London Roofing friend swears by heat tape you can stick along the gutter. Personally, I don’t feel that this is necessary provided you keep them clear.
 • Snow guards can provide an extra line of defence, especially if you live up in the north, and they can help keep the gutters clear in summertime too. In fact, I strongly recommend them.
Hopefully you did this already and your gutters won’t come crashing down from the weight of ice this winter. Please do be careful about venturing on the roof yourself to clear excessive snow. It’s just not worth taking risks.
And that’s where Mr-Skill comes in. Did you know that you can Find a Gutter Man right here who’ll clear your blocked gutters promptly, as long as it’s not actually snowing? All our trades come highly recommended too, and rated by our customers. What’s more, you pay nothing for our services.
Tags: blizzard, ceiling, clean, clear, collapsing, down pipe, find a roofer, freeze, freezing, gutter, gutterman, heat, heat tape, ice, insulate, london roofing, melt, roofer, roofing quote, snow guard, test, thaw, ventilate, water, winter
Posted in Roofing, Gutters & Drainage | Comments Off
Posted in Cleaning Services on Jan 25
It’s annoying, isn’t it, how you find stains on the lounge carpet the day after you have good friends around for a party. Let’s give them the benefit of the doubt and get on with sorting out the mess. If they’re  badly soiled, you’d best Get a Cleaning Quote on Mr-Skill. If not, the following hints should prove helpful.
- Chewing Gum Freeze the gum with a few blocks of ice in a plastic bag. After it’s gone hard, pick it off with a knife.
- All Stains (Step 1) Get rid of the source of the problem by mopping up any remaining liquid. DO NOT WORSEN THINGS BY RUBBING.
- Grass / Cool Drink Stains Dab the area with a cloth moistened with diluted detergent.
- Oil and Grease Stains Dab with a cloth soaked in a non-flammable dry cleaning agent. TEST AN
 INCONSPICUOUS AREA FIRST.
- Coffee Stains Sponge with a solution of borax. Some London Cleaners believe that more resistant stains may respond to beaten egg-yolk.
- Lipstick Stains Treat with methylated spirits or salad oil. Afterwards, soak the stain in lemon juice, which must be diluted 50:50 with water unless the carpet is pure white.
We provide this information in good faith as it was passed on to us.
If in any doubt, we’d far prefer you to Find a Cleaner on our Website instead, because we are unable to guarantee it. Either way, it’ll be nice to have the lounge carpet back in good condition again thanks to Mr-Skill.
Tags: borax, carpet, chewing gum, cleaning quote, coffee, cool drink, detergent, dry cleaning, egg yolk, find a cleaner, freeze, grass, grease, gum, ice, lemon juice, lipstick, liquid, london cleaner, methylated spirits, mop, oil, rub, salad oil, stain, test
Posted in Cleaning Services | Comments Off
Posted in Carpentry & Joinery on Nov 08
Bedroom fitters seem to find it necessary to install cupboards from the wall to ceiling. While this makes sense in terms of managing the dust on top, customers often end up with storage space that looks more like the inside of a church steeple. The solution? Add a space below for storing shoes, or above for keeping what almost inevitably turns out to be junk.
 I personally don’t have much time for using the plastic shelf blocks that seem all the rage these days. That’s because they involve point contact and it’s difficult to get them aligned perfectly. Moreover, in these times of chipboard everything, an overloaded shelf can easily come crashing down.
The following is what Professional London Carpenters still prefer to do:
• Remove the cupboard doors for ease of access and to avoid straining hinges. Measure the internal depth of the cupboard from front to back at both left and right. While you’re at it, measure the cupboard internally from left to right too. Enter the information on a drawing, because in all the years of providing Carpentry Quotes I have seldom come across a cupboard that’s perfectly square.
• Ask the hardware store to cut a shelf to size and to cut battens to support it on the left and right too. Make sure they also supply half-a-dozen screws of the appropriate length.
•  Pre-drill the battens in the middle and towards either end. Fix the first one in the middle only and set it horizontal with a spirit level. Draw a pencil line along the bottom edge and fit the other two screws accordingly.
• Measure from the top or bottom of the cupboard to determine where the second batten should go. Screw it into place, again just using the middle hole. Test fit the shelf in place. It should be level and fit snugly so you can complete the installation and replace the doors. If not, you may need to make adjustments.
You could also save yourself a heap of trouble and get Highly Competitive Carpentry Quotes on Mr-Skill instead. We have carpenters at every UK postcode. They’re on standby to fit that shelf for you, and much more.
Tags: battem, bedroom, block, bottom, carpentry quotes, chipboard, complete, cupboard, cut, door, drill, dust, find a carpenter, fit, hinge, horizontal, length, london carpenters, measure, plastic, remove, replace, screw, shelf, shoe, size, snug, spirit level, square, storage, strain, support, test, top, vertical, weight
Posted in Carpentry & Joinery | Comments Off
Posted in Electrical Work on Oct 25
Although they may appear complex, electric stoves are actually very basic apparatuses concealed in fancy metal cabinetry. Suppliers build them to last a lifetime safely – if they give problems, the cause is almost inevitably a switch or element that has failed. A householder may legally replace components like these, provided the stove is wired via a safety breaker to the switchboard.
 If your stove does not have a breaker switch on the kitchen wall do not follow these instructions. Find an Electrician instead.
• Obtain the correct replacement switch from an authorised dealer. Do not be tempted to buy a pirate part.
• Turn off the breaker switch and make sure that the stove is isolated. Tape over the switch so that it cannot be inadvertently turned on again.
• Electric switches on modern stoves are mounted on a panel below the cooking surface. Lever off the control knob and remove this panel which is held in place with screws.
• Remove the screws attaching the offending switch to the panel on the inside, and draw it away. Make a drawing of how the different coloured wires are connected.
•  Transfer these wires one by one from the old switch to the new one. Electricians in London like to call this monkey see – monkey do. When done, compare the result with the drawing to make double sure.
• Attach the new switch inside the control panel. Replace the panel after making sure that everything behind it is perfectly connected, and that no wire is in contact with the metal casing. Refit the control knob.
• Make sure all the stove switches are turned off. Turn on the breaker switch on the kitchen wall. Test all the other stove circuits first, and then the switch that you replaced. Everything should be perfect. If not, then there is another problem. You urgently need to get a Professional Electrical Quote.
If at any time you notice anything untoward inside your stove, stop immediately and Find an Electrician on Mr-Skill. Do not take chances with electricity! Electricity has the power to kill.
Tags: attach, breaker, check, colour, cooker, drawing, electric, electrical quote, element, find an electrician, isolate, kitchen, knob, london electricians, panel, pirate, problem, remove, replacement, safe, screw, stove, switch, test, wall, wire
Posted in Electrical Work | Comments Off
The kitchen truly is at the heart of every home, and if you think about it the sink tap is at its core. First thing in the morning we use it to fill the kettle. Last thing at night we rinse the dirty dishes. Cook uses it at least a dozen times a day. The family gathers around it to do the washing up.
 There are some really handsome kitchen taps around these days. Why not Find a Plumber and spoil yourself with a new one. If you are thinking of doing it yourself, then here’s what’s involved.
1. Isolate the hot and cold water supply, making sure the flow stops completely. Position a bucket beneath the tap under the sink.
2. Loosen off the nut that holds the tap in place. London Plumbers always travel with a basin wrench – if the nut is hard to get at, you’ll know why.
3. Disconnect the flexible water lines connecting the tap to the water supply at the lower end. Be careful not to strain the piping. As you remove the couplings a little water will flow out. Make sure the bucket is in place before you do!
4. Remove the old tap complete with the flexible pipes attached. Clean the sink surface thoroughly where the old tap rested. Take your time to do this properly. Apply a  generous bead of plumbers putty around the hole in the surface of the sink, and gently bed the rubber gasket into it.
5. Insert the new tap assembly through the hole including the flexible water lines. Locate the fixing nut, position the tap, and tighten the nut firmly. Attach the pipes to the water supply remembering to be generous with plumber’s tape.
6. Re-tighten the nut that secures the tap as it will have bedded down. Remove the surplus putty that squeezed out and clean the sink top thoroughly. Turn on the water and test the tap. No leaks? You’ve earned a cup of tea and a biscuit too!
Sound’s easy, doesn’t it? But there are various things that could go wrong, resulting in water leaks that could ruin expensive kitchen cabinetry. Why not get a Plumber’s Quote on Mr-Skill instead? You’ll save pounds off normal rates, and could still enjoy that cup of tea and biscuit.
Tags: attach, basin, bucket, change, clean, cold, flexibly, flow, gasket, heart, home, hot, insert, isolate, kitchen, leak, line, loose, nit, pipe, putty, rubber, save pounds, sink, supply, surplus, tap, tape, test, tight, water, wrench
Posted in Plumbing, Heating & Gas | Comments Off
Posted in Carpentry & Joinery on Sep 24
Oftentimes the simplest things are the most enjoyable. Like a small child playing with a paper boat in a stream, or a couple walking hand-in-hand along a river bank. To me though, the gentle sound of a bamboo wind chime resonating gently in the garden is the best sound of all. The good news is that these delightful inventions are so easy to make, that there’s no need to Find a Joiner this time at all.
•  Obtain some lengths of bamboo from the hardware shop or garden centre. These need to be dry so that they resonate nicely, and be of different diameters too.
• Cut different lengths of bamboo from each source. There are two principles here. The diameter affects the depth of resonance or tone, while the length affects the pitch. Remember to ensure that there are no segments within the length you cut, or else the sound will not travel between the ends.
• Knock the lengths of bamboo together gently to check results. You can even tune them by adjusting lengths. Some pieces will work better against each other – these are the ones you need to juxtapose as some do at better London Joining Firms.
• Finish off your bamboo pieces with shaped lower ends like organ pipes. This is done by removing one-half of the last inch or so and tidying up. Some say this affects the pitch. Others like me just think it just looks better that way.
•  Drill holes through the top ends for the hanger-strings. Remember to make these parallel to the bottom detail, so that these all present the same by facing outwards. Attach the strings ensuring they are of the same length, and tie the ends together neatly before hanging the set in an appropriate place that will catch the wind.
• Obtain a spreader disc of an appropriate diameter, and notch it deeply to receive the hanger strings. Set this in place between the strings and hey-presto you have a wooden wind chime. Finally, secure the strings to the spreader disc with hot-melt glue.
How’s that for a bit of fun for a Sunday’s home entertainment. And you don’t need Carpenter Quotes either. Although Mr-Skill is a serious business that matches clients and skilled tradesmen, we also like to give good ideas away. You can decorate your bamboo wind pipes any way you want. Did you notice how easy it is to rearrange the pipes.
Tags: adjust, bamboo, build, carpenter quote, chime, cut, decorate, diameter, drill, easy, end, find a joiner, finish, Garden, garden centre, gentle, hand, hardware shop, juxtapose, knock, length, london joining firm, make, notch, pitch, resonance, resonate, segment, simple, spread, string, test, tone, tune, wind, wind chime
Posted in Carpentry & Joinery | Comments Off
Colour comes free, as my dad who used to work for London Painters until he retired a few years ago loves to say. Or almost free that is, unless you decide to have it specially tinted. This means that the cost of a boring or an exuberant colour scheme is  approximately the same, provided that is you use your imagination.
• The basis of any decorating scheme lies in the juxtaposition of the colours. Choose Tonal when you play with shades of the same colours, or perhaps the same intensity of different ones. Harmonious effects are created by choosing adjacent tints. Complementary colour schemes do exactly that by using opposites.
• The next step is to create a mood. Warm, advancing colours welcome people on cooler days, while cooler, watery colours relax one at any time. Remember that lighting can add dramatic or unexpected effects at different times of day, and in different seasons.
• Inspiration is often found in nature as if it is the work of genius, because the colour combinations often work so well. Try looking at the interior shades of seashells and autumn leaves. Chances are you will be amazed at what you find.
•  Homes should be calm relaxing places, and after you Find a Decorator you do need to discuss a strategy for linking rooms, so that the contrasts do not jar. Think about using Tonal or Harmonious effects to achieve the best results. Door colours require great thought too, which is perhaps so many doors are white these days.
• Before getting started after deciding among your Painting Quotes, please do put up a few test panels first. Any painter you find on Mr-Skill will advise how best to deal with underlying existing colours when you do.
That’s all there really is to a Best Colour Scheme. A little thought, a few test panels and you are almost on your way. If you find the thought of doing the job yourself off-putting though, then why not Find a Painter on Mr-Skill instead?
Tags: calm, colour, complementary, cool, cost, day, decorate, decorator, door, find a decorator, find a painter, free, harmonious, imagination, inspiration, intensity, link, london painters, mood, nature, night, opposite, paint, painter, painting quote, panel, relax, season, test, time, tint, tonal, warm, welcome
Posted in Painting & Decorating | Comments Off
Climbing ivy is undoubtedly a sight to behold as spread out across a wall and creates an environment in which the birds may nest. But it has its disadvantages too. Snakes and spiders and even rats may use it to gain access to your bedroom, and it can also cause damage to bricks, window frames and gutters.  Are you of a mind to get rid of yours? Then you may need to Find a Gardener on Mr-Skill to do the work for you. That’s because standing on a ladder all day is dangerous, and the job is laborious too. Not convinced to call in help? Then here is what you need to do…
• Pull a test sample of ivy away from the wall to determine how thick it is, and whether it tears off without causing damage. If it comes away easily then you could continue. If not, then you may need to get Gardening Quotes to have poison applied by an expert, and perhaps even call in a builder afterwards to make repairs.
• Returning to ground level, lop off all the vines as close as possible to the ground before proceeding to peel away the cut branches. Be careful here, because a sheet of ivy can come loose unexpectedly, and this will be heavy and surprisingly dusty too. Do not attempt to deal with the tiny hand-like suckers yet.
•  Bag the cuttings and dispose of them at your local council dump-site according to the bylaws.
• After approximately two to three weeks, remove the suckers with a stiff wire brush covered with approximately two tablespoons of household laundry detergent. Every Gardener in London knows all too well not to miss the deadline. That’s because beyond this period the suckers oxidize, and are stubborn to remove.
So there you go. It’s not really all that difficult to get ivy off a wall. It’s just a messy, time-consuming job. Not in the mood to do it anymore? Then speak to Mr-Skill about the services of a Rated Local Gardener.
Personally, I find the patina of natural brickwork far more appealing, especially on an older building.
Tags: away, bag, bird, brick, builder, cutting, damage, danger, detergent, dispose, dust, expert, find a gardener, gardener in London, gardening quotes, ground, gutter, heavy, help, ivy, ladder, loose, lop, peel, poison, pull, rat, repair, sample, snake, sucker, tear, test, vine, window, wire brush, work
Posted in Gardening & Landscaping | Comments Off
Posted in Electrical Work on Aug 04
A dimmer switch has the effect of turning down the electricity in much the same way as turning down a tap reduces the flow of water (although that is just an analogy). It is a simple, cheap improvement that adds ambiance to any room. Just be aware that dimmers do not work on fluorescent tubes and some low energy bulbs, at least as yet.
o  Obtain a suitable dimmer switch that matches your current installation and is suitable for use in the UK. Turn off the power at the mains and double check that the power at the switch is dead by turning on the light switch. I learned this trick from a wizened old Electrician in London who liked to say if it’s wired to bypass the mains switch then it won’t be the first one that I have seen.
o Remove the cover plate over the existing light switch and withdraw the switch itself. Before removing any wires from it make a simple diagram noting how each colour wire is connected. This is to avoid needing an Electrician Quote in case you end up having to reinstall it and forgot which wire went where.
o Remove the wires from the existing switch and set it to one side. You might like to keep it in your bottom drawer because you never know when you might need it. Gently draw any slack wire out from the wall and check it carefully for any damage. If the wire ends are getting frayed give them the necessary attention.
o  Connect the wires to the replacement dimmer switch according to the instructions, making sure that it is correctly orientated so it will slide neatly into the recess, remembering to tighten the screws up nicely. Now take a five minute break for reasons I will disclose. Have a cuppa tea, exercise your dog, show your wife how much you love her – in fact do anything you like that takes five minutes or even more.
o Re-tighten the screws that hold the dimmer wires in place noting how the wires under them have settled. This is the single most likely reason why wires sometimes still come loose, and is a secret you might well like to pass on to a friend. Press the dimmer switch gently into position, screw it down and refit the cover plate to complete the job.
Now you can turn the main switch on again and test your job. Not working? Check the bulb. Still not working? You may not need to Find an Electrician yet. Remove the dimmer switch and have it tested. Now aren’t you glad you made a diagram of how the old switch was connected.
Tags: ambiance, bypass, cheap, check, colour, connect, correct, cover, diagram, dimmer, electrician in london, electrician quote, energy, find an electrician, fluorescent, inspect, installation, light, loose, main switch, mains, off, plate, power, recess, save, screw, settle, slack, slide, suit, switch, test, tight, uk, wire
Posted in Electrical Work | Comments Off
|
Subscribe to our RSS Feed